Skip to content


Blown-in insulation is one of the tried-and-true home improvement methods for keeping the winter cold at bay. The method of stuffing insulation into your walls has been Eco Grants found quite difficult by most people. But the attempts are worthwhile, because they turn your old energy-liberal house into an energy saver.

fiberglass , foam or cellulose, the blowing-in process has countless variations. Retrofitting these materials into the leaky walls or attic allows your home to retain heat. In this way, your house becomes an energy saver and reduces energy consumption, since no heating systems are required to warm up the indoor temperature. Therefore, you can reduce your energy costs by 20 to 30 percent. So wouldn’t you want to use blown-in home insulation to control thermal swings and keep chilly winds at bay?

Common insulation materials for home

Blow-in insulation can be carried out by selecting all common house insulation materials. Once installed, the effect of this typical insulation is guaranteed and lasts for the entire life of the house. However, the inconvenience of blowing in materials deters most homeowners from undertaking it. Even the most determined DIY enthusiast finds it difficult to obtain the necessary equipment and difficult to learn how to use the equipment and the problems associated with blow-in insulation.

In the face of such inconveniences, it is best to entrust your home thermal insulation project to a registered professional. In addition, the participation of a registered installer is associated with the guarantee seal that guarantees effectiveness for up to 25 years. So if a certain area that gives off heat and receives cold air from outside is insulated after the blow-in method, it becomes completely resistant to heat transfer.

Attic insulation and insulation

Fiberglass-based home insulation is best for attic insulation and insulation of other hard-to-reach areas. The installation of GRP – insulating materials is quite critical for laypeople. Also, fiberglass materials tend to fluff up when inflated into the target area due to lack of care and methodical approaches. Therefore, it is recommended that fiberglass materials be left to professional contractors to avoid risk and ensure optimal insulation performance.

When selecting an insulating material, it is imperative to follow government and manufacturer recommendations and precautions, consider the R-value of the materials and also comply with the mandatory achievable depth (per square foot).

Home Insulation Guide – Calculate how much insulation you need

The process of home insulation is applicable to convert all areas of your home against heat loss. Whether the home’s attic, floors, windows and doors, or floors are catalysts for heat loss, seal out drafts with proper insulation methods. Even when air conditioning is used, valuable and artificially conditioned air is lost in your house due to a lack of insulation. When insulation is added in the right proportion, it retards the natural tendency for heat to move from a warmer location to a cooler area exiting the home, and also delays the entry of cold air into the home. Likewise, a properly insulated home will keep the scorching heat out of the home. How much insulation your property needs varies from property to property and also depends on the climate. Do you know how much insulation your house needs?

Home insulation measurement

One has to decide what type of insulation is needed and in what ratio. The best way to know is by calling utility professionals who provide information through “Energy Audit”. They make a full assessment of the availability of drafts in the home and the area should be sealed with insulation treatment. The effectiveness of any type of insulation is measured by the R-value, or resistance value, of the material used in the insulation. Home insulation materials vary in their R-value, or heat resistance, which is provided by every inch of thickness.

The R-value tends to differ in different climate zones

The R-value tends to vary depending on climate and building design. In mild climates, the right ratio for wall and floor insulation should be R-11, while for attic insulation it should be R-19. Likewise, in temperate regions, R-19 is the right amount of insulation for floors and walls, and R-30 is appropriate for roofs. Buildings in the colder climates require R-19 wall insulation and floor insulation, approximately R-38 to 49 for the ceiling area.

To calculate the required amount of home insulation on top of Eco Grants the existing insulation layer, you must first turn off the power to the home. You should also unscrew the outlet cover and put a hanger in the open space. Use a hanger to measure the depth available to run insulation in that space. At the same time see what type of insulation has been added to the area by removing some insulation with the hanger. You can also contact an insulation survey company or professional to inspect the insulation you have and need and give you a detailed assessment.

Notify of
Inline Feedbacks
View all comments